Application
High (mains) pressure systems.
Features/Benefits
- Pressure compensated to give constant outlet pressure regardless of inlet pressure.
- N.Z. forged, high quality, corrosion resistant DR brass body
- Machined, assembled and 100% tested in N.Z.
- No tools required to service valve.
- Valve is adjustable (200 - 600 kPa [29 - 87psi]) with Philips screw driver.
- All valve seats and pistons are contained in the easily replaceable cartridge
- Valve cartridge does not need reassembling to clean filter.
- Removal of cartridge will not affect the set pressures.
- No pipe unions, no leaks!
Video
 |
Limiting Stop Valve. |
| Run-time: 52 seconds |
 |
|
Standards
- Complies with NZ Building Code G12 (2001)
- Manufactured to NZS 4608: 1992
- Cartridge Water marked AS1357.2 LICWMKA 02596
Specifications
| LV15 |
Inlet |
15mm, 1/2" BSP (male) |
| Outlet |
20mm, 3/4" BSP (male) |
| LV20 |
Inlet |
20mm, 3/4" BSP (female) |
| Outlet |
20mm, 3/4" BSP (male) |
| LVT15 |
Inlet |
15mm, 1/2" BSP (male) |
| Outlet |
20mm, 3/4" BSP (male) |
| LVT20 |
Inlet |
20mm, 3/4" BSP (female) |
| Outlet |
20mm, 3/4" BSP (male) |
- High flow rates up to 135 l/m.
- Maximum inlet pressure: 1600 kPa [230psi].
- Integral 60 mesh (250 micron) strainer.
| LV25 |
Inlet |
25mm, 1" BSP (male) |
| Outlet |
25mm, 1" BSP (male) |
| LV32 |
Inlet |
32mm, 1 1/4" BSP (male) |
| Outlet |
32mm, 1 1/4" BSP (male) |
- Extremely high flow rates up to 250 l/m.
- Twin adjustable (200-600 kPa)
- Twin, integral 60 mesh (250 micron) strainers.
| LSV20 |
Inlet |
20mm, 3/4" BSP (male) |
| Outlet |
20mm, 3/4" BSP (male) |
- Compact 4-in1 valve - limiting, isolating, non-return and filter all in one.
- High flow rates up to 135 l/m.
- Can be installed outside (with cartridge down)
| LVA |
Inlet |
20mm, 3/4" BSP (female) |
| Outlet |
20mm, 3/4" BSP (male) |
| LVRA |
Inlet |
20mm, 3/4" BSP (female) |
| Outlet |
20mm, 3/4" BSP (male) |
| Length |
LV (all models except LV25 & LV32) |
80mm |
| LV25 |
110mm |
| LV32 |
115mm |
| LSV |
140mm |
| LVRA |
70mm |
- Maximum inlet pressure: 2000 kPa
- Maximum inlet temperature: 65˚C.
- Minimum temperature: 1˚C.
Flow Chart
Installation
- Refer to Technical Area
for installation guide.
- Do NOT install Limiting Valve in the ground.
- Do NOT apply heat near valve during installation.
- Install so that both hot and cold supplies are balanced.
- Can be installed in any orientation. For external application, cartridge must be at
bottom.
- Must be installed with correct Expansion Valve fitted down stream of a limiting valve.
- To adjust outlet pressure use large Philips/Pozi screw driver, turn adjusting screw
clockwise to increase (1 turn = 60 kPa [9psi]).
Removable Cartridge
- All valve seats are contained within cartridge.
- No need to remove body from valve train.
- Unscrew cartridge to replace or clean filter.
- Removal of cartridge will not affect set pressure.
Servicing
- Filter must be cleaned regularly.
Sectional Views
| LV15 & LV20 |
 |
| LV25 only |
 |
| LSV |
 |
| LVRA |
 |
|
|
 |
|
|
Brochure
Download the new LV25 and LV32 Pressure Limiting Valve brochures in PDF* format or contact us to have
them sent to you.
Download LV25 as PDF
Download LV32 as PDF
*Requires Adobe Acrobat Reader to be installed.
Product Codes
| LV15-350 |
350 kPa |
Use with EVT500 |
| LV15-500 |
500 kPa |
Use with EVT700 |
| LV20-350 |
350 kPa |
Use with EVT500 |
| LV20-500 |
500 kPa |
Use with EVT700 |
| LV25-500 |
500 kPa |
Use with EV25 |
| LV32-500 |
500 kPa |
Use with EV32 |
| LVT15-350 |
350 kPa |
Use with EVT500 |
| LVT15-500 |
500 kPa |
Use with EVT700 |
| LVT20-350 |
350 kPa |
Use with EVT500 |
| LVT20-500 |
500 kPa |
Use with EVT700 |
| LSV20-350 |
350 kPa |
Use with EVT500 |
| LSV20-500 |
500 kPa |
Use with EVT700 |
| LVA20-350 |
350 kPa |
Use with 500 kPa Expansion Control Valve |
| LVA20-500 |
500 kPa |
Use with 850 kPa Expansion Control Valve |
| LVA20-600 |
600 kPa |
Use with 850 kPa Expansion Control Valve |
| LVRA20-350 |
350 kPa |
Use with 500 kPa Expansion Control Valve |
| LVRA20-500 |
500 kPa |
Use with 850 kPa Expansion Control Valve |
| LVRA20-600 |
600 kPa |
Use with 850 kPa Expansion Control Valve |
Note: All limiting valves must be protected by a downstream expansion valve of the relative
setting as prescribed in the table above. |
